< prior
Back to Month
Go to Thread
2016-08-25; 20:32:27 EDT
Member Since
2012-01-04
Posts: 260
Haha! Strong back. Very small head! Bob (palatka)See the original archive post
> On Aug 24, 2016, at 10:43 PM, Chris Geankoplis <chrisgeankoplis at gmail.com> wrote: > > Bob, > Why do I have a picture of you as Atlas? > Chris G > >> On Sun, Aug 21, 2016 at 9:29 PM, Goodness <spreadgoodnews at gmail.com> wrote: >> >> Graham: Being the foolish and impatient type, i used my back, stood up >> under the top pressing my back into it and put a 4x4 post with a cloth over >> the top under it to support then tapped the compression post and bulkhead >> in place with a mallet. Then i tapped out the 4x4 and the compression post >> was firmly in place. Right or wrong, I didnt give it 2 minutes of though! >> I was certain i had the base at the right height as i had made templates >> before i deconstructed the rotten base. I just assumed the wide span of >> the fiberglass head liner was heavy and sagged. My deck always remained >> rock solid. >> Bob (palatka) >>> On Aug 21, 2016, at 9:08 AM, Graham Stewart <gstewart8 at cogeco.ca> wrote: >>> >>> BoB: >>> >>> Thanks for the feedback. That is very helpful. >>> Yes, I had unstepped the mast and there was no load on the deck - not >> even >>> snow. I made the new bulkhead pieces using the old ones as templates and >>> placed them according to the fibreglass stubs that were in place to hold >> the >>> old pieces. Everything seems to be coming together properly so I am >> pretty >>> sure that the compression post base is in the correct place. The only >>> difference is that the old base had been distorting under the force of >> the >>> compression post over the years so the new piece corrected for that >>> accounting for perhaps as much as 1/2 inch in the drop of the cabin top. >>> What did you use to raise the cabin top in order to reinsert the >> compression >>> post? How much force did it take? >>> Thanks again, >>> >>> >>> Graham Stewart >>> Agile. R22, 1976 >>> Kingston Ontario Canada >>> >>> >>> >>> >>> -----Original Message----- >>> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On >> Behalf Of >>> Goodness >>> Sent: August 20, 2016 11:09 PM >>> To: The Rhodes 22 Email List >>> Subject: Re: [Rhodes22-list] deck shape >>> >>> Graham: i assume that your mast has remained unstepped during your >>> restoration. >>> Remember you have an inner hull so your cabin top has two layers. The >> center >>> of my cabin top interior dropped an inch immediately upon removing my >>> compression post. I had the floor bulkhead replaced within a week but >> had >>> to lift the inner lining up to get the compression post to fit back into >>> place. It is nice and tight and the deck is level and firm. Fiberglass >> is >>> very flexible and strong. Make sure your base for the post is at the >> proper >>> height however. Do you have an original bulkehad as well? That helps >> you >>> guage that the compression post is in the right position. >>> Good luck! >>> >>> Bob (palatka) >>> >>>> On Aug 20, 2016, at 7:25 PM, Graham Stewart <gstewart8 at cogeco.ca> >> wrote: >>>> >>>> I am finally at the point in my restoration of Agile where am >>>> installing the compression post and main bulkhead. However, it appears >>>> that the cabin top has dropped by a full inch. I am left with the >>>> choice of either jacking up the deck so that the compression post fits >>>> or cutting the post back to fit the space. Does anyone know what the >>>> implications might be if I gradually jack up the cabin top? Might I >>>> crack the deck? Obviously I should have supported the cabin top when I >>>> removed the post but I didn't think it would deform when there was no >> load >>> on it. >>>> >>>> If anyone has any suggestions I would appreciate it. Otherwise I will >>>> try to rais the top very gradually and if that seems to require more >>>> than a moderate force I will live with the missing inch and tell >>>> myself that I am still growing. >>>> >>>> >>>> Graham Stewart >>>> Agile. R22, 1976 >>>> Kingston Ontario Canada >>>> >>>> >>>> >>>> >>>> >>>> __________________________________________________ >>>> To subscribe/unsubscribe go to >>>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>>> >>>> For the list Charter and help with using the mailing list and archives >>>> go to http://www.rhodes22.org/list >>>> __________________________________________________ >>> __________________________________________________ >>> To subscribe/unsubscribe go to >>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>> >>> For the list Charter and help with using the mailing list and archives >> go to >>> http://www.rhodes22.org/list >>> __________________________________________________ >>> >>> __________________________________________________ >>> To subscribe/unsubscribe go to http://www.rhodes22.org/ >> mailman/listinfo/rhodes22-list >>> >>> For the list Charter and help with using the mailing list and archives >> go to http://www.rhodes22.org/list >>> __________________________________________________ >> __________________________________________________ >> To subscribe/unsubscribe go to http://www.rhodes22.org/ >> mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and archives go >> to http://www.rhodes22.org/list >> __________________________________________________ > __________________________________________________ > To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list > __________________________________________________
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 