< prior
Back to Month
Go to Thread
2016-08-25; 21:04:10 EDT
Member Since
2004-04-05
Posts: 2062
On Thu, Aug 25, 2016 at 8:32 PM, Goodness <spreadgoodnews at gmail.com> wrote: > Haha! Strong back. Very small head! > > Bob (palatka) > > > On Aug 24, 2016, at 10:43 PM, Chris Geankoplis < > chrisgeankoplis at gmail.com> wrote: > > > > Bob, > > Why do I have a picture of you as Atlas? > > Chris G > > > >> On Sun, Aug 21, 2016 at 9:29 PM, Goodness <spreadgoodnews at gmail.com> > wrote: > >> > >> Graham: Being the foolish and impatient type, i used my back, stood up > >> under the top pressing my back into it and put a 4x4 post with a cloth > over > >> the top under it to support then tapped the compression post and > bulkhead > >> in place with a mallet. Then i tapped out the 4x4 and the compression > post > >> was firmly in place. Right or wrong, I didnt give it 2 minutes of > though! > >> I was certain i had the base at the right height as i had made templates > >> before i deconstructed the rotten base. I just assumed the wide span of > >> the fiberglass head liner was heavy and sagged. My deck always remained > >> rock solid. > >> Bob (palatka) > >>> On Aug 21, 2016, at 9:08 AM, Graham Stewart <gstewart8 at cogeco.ca> > wrote: > >>> > >>> BoB: > >>> > >>> Thanks for the feedback. That is very helpful. > >>> Yes, I had unstepped the mast and there was no load on the deck - not > >> even > >>> snow. I made the new bulkhead pieces using the old ones as templates > and > >>> placed them according to the fibreglass stubs that were in place to > hold > >> the > >>> old pieces. Everything seems to be coming together properly so I am > >> pretty > >>> sure that the compression post base is in the correct place. The only > >>> difference is that the old base had been distorting under the force of > >> the > >>> compression post over the years so the new piece corrected for that > >>> accounting for perhaps as much as 1/2 inch in the drop of the cabin > top. > >>> What did you use to raise the cabin top in order to reinsert the > >> compression > >>> post? How much force did it take? > >>> Thanks again, > >>> > >>> > >>> Graham Stewart > >>> Agile. R22, 1976 > >>> Kingston Ontario Canada > >>> > >>> > >>> > >>> > >>> -----Original Message----- > >>> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On > >> Behalf Of > >>> Goodness > >>> Sent: August 20, 2016 11:09 PM > >>> To: The Rhodes 22 Email List > >>> Subject: Re: [Rhodes22-list] deck shape > >>> > >>> Graham: i assume that your mast has remained unstepped during your > >>> restoration. > >>> Remember you have an inner hull so your cabin top has two layers. The > >> center > >>> of my cabin top interior dropped an inch immediately upon removing my > >>> compression post. I had the floor bulkhead replaced within a week but > >> had > >>> to lift the inner lining up to get the compression post to fit back > into > >>> place. It is nice and tight and the deck is level and firm. > Fiberglass > >> is > >>> very flexible and strong. Make sure your base for the post is at the > >> proper > >>> height however. Do you have an original bulkehad as well? That helps > >> you > >>> guage that the compression post is in the right position. > >>> Good luck! > >>> > >>> Bob (palatka) > >>> > >>>> On Aug 20, 2016, at 7:25 PM, Graham Stewart <gstewart8 at cogeco.ca> > >> wrote: > >>>> > >>>> I am finally at the point in my restoration of Agile where am > >>>> installing the compression post and main bulkhead. However, it appears > >>>> that the cabin top has dropped by a full inch. I am left with the > >>>> choice of either jacking up the deck so that the compression post fits > >>>> or cutting the post back to fit the space. Does anyone know what the > >>>> implications might be if I gradually jack up the cabin top? Might I > >>>> crack the deck? Obviously I should have supported the cabin top when I > >>>> removed the post but I didn't think it would deform when there was no > >> load > >>> on it. > >>>> > >>>> If anyone has any suggestions I would appreciate it. Otherwise I will > >>>> try to rais the top very gradually and if that seems to require more > >>>> than a moderate force I will live with the missing inch and tell > >>>> myself that I am still growing. > >>>> > >>>> > >>>> Graham Stewart > >>>> Agile. R22, 1976 > >>>> Kingston Ontario Canada > >>>> > >>>> > >>>> > >>>> > >>>> > >>>> __________________________________________________ > >>>> To subscribe/unsubscribe go to > >>>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list > >>>> > >>>> For the list Charter and help with using the mailing list and archives > >>>> go to http://www.rhodes22.org/list > >>>> __________________________________________________ > >>> __________________________________________________ > >>> To subscribe/unsubscribe go to > >>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list > >>> > >>> For the list Charter and help with using the mailing list and archives > >> go to > >>> http://www.rhodes22.org/list > >>> __________________________________________________ > >>> > >>> __________________________________________________ > >>> To subscribe/unsubscribe go to http://www.rhodes22.org/ > >> mailman/listinfo/rhodes22-list > >>> > >>> For the list Charter and help with using the mailing list and archives > >> go to http://www.rhodes22.org/list > >>> __________________________________________________ > >> __________________________________________________ > >> To subscribe/unsubscribe go to http://www.rhodes22.org/ > >> mailman/listinfo/rhodes22-list > >> > >> For the list Charter and help with using the mailing list and archives > go > >> to http://www.rhodes22.org/list > >> __________________________________________________ > > __________________________________________________ > > To subscribe/unsubscribe go to http://www.rhodes22.org/ > mailman/listinfo/rhodes22-list > > > > For the list Charter and help with using the mailing list and archives > go to http://www.rhodes22.org/list > > __________________________________________________ > __________________________________________________ > To subscribe/unsubscribe go to http://www.rhodes22.org/ > mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to http://www.rhodes22.org/list > __________________________________________________ >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 