< prior
Back to Month
Go to Thread
2016-08-25; 23:00:39 EDT
Member Since
2005-04-29
Posts: 816
For me the cost of the Tessilmare was considerably more than the Tyco but that might be because I am in Canada. Graham Stewart Agile. R22, 1976 Kingston Ontario CanadaSee the original archive post
-----Original Message----- From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of Chris Geankoplis Sent: August 25, 2016 9:30 PM To: The Rhodes 22 Email List Subject: Re: [Rhodes22-list] Tessilmare Radial Flexible Rub Rail Thanks for this very useful write up. I used the teco and it was a PTA. Looked great but cost a lot more than your system and was no better in quality. Next time I'll use this product. Chris Enosis On Thu, Aug 25, 2016 at 12:23 AM, Graham Stewart <gstewart8 at cogeco.ca> wrote: > For those who might be replacing their rub rail I thought I would post > some notes and a picture of my boat after installing the Tessilmare > Radial Flexible Rub Rail system.(see: > http://www.jamestowndistributors.com/ > userportal/show_product.do?pid=56893 > > The system comes in two parts: a plastic track and a rubber bumper. > The track comes in 6' lengths and the rubber rail is continuous in the > length you choose. I ordered 55' and that worked out fine with about 3 feet extra. > > The primary reason I choose this system was because installing it can > be accomplished working alone. I didn't want to have to find and then > depend on someone to help. Unlike the more popular Tacho system the > rubber rail does not need to be stretched during installation. In > fact, I was able to install it alone so that worked out fine. However, > the time it took was considerably longer than what was implied in the sales material. > > The track goes on with screws. It is fairly soft plastic and if the > screws are driven in too tight the track bulges around the screw and > this deformation shows when the rubber rail is installed. As it turned > out, and in spite of various approaches, I was not able to find the > perfect setting where the screw was sufficiently tight without > creating the bulge. The only way I could avoid the bulges in the > rubber rail was to use a box cutter to shave off the sides of each > bulge on the track. That was not difficult but it was time consuming. > You can see in the attached picture slight dimples in the rubber rail > where each screw is located. You only see them when you look along the rail with the light reflecting off the surface. > > They recommend screws but say that rivets could also be used. Rivets > would compress the track much more tightly than screws and would bulge > the track considerably more so I don't see rivets as being practical. > So unlike the original rub rail I was not able to use rivets to > install the rail and secure the hull/deck join at the same time. I > riveted the join first and then installed the track with screws. I > used 1 1/2" screws but should have used 1" screws. > > Screws go in easily and are spaced every 6 inches. After drilling the > hole for the screw I squeezed a dab of sealant into the hole. I > suspect that had little effect in creating a seal - but I can't be sure. > > The sales material implied that the track can be bent around corners > and the bow without the use of heat. Once you get the kit you find out > that a bend in excess of a 40 mm radius required the application of > heat. In the case of the Rhodes the bow and both ends of the transom > are too sharp to avoid using the heat. That said, it does not require > a lot of heat. I used my heat gun on the low setting and moved it back > and forward along the track while I slowly bent it around the bend. > However, you need to put a length of wire under both tabs in the track > to avoid having them lose their shape and make it impossible to fit > the rubber rail later. I used pieces of coated clothes line wire and that worked perfectly. > > To install the rubber rail you bend it back to spread the tabs that > grab onto the track and roll the rail forward. By the time I was > finished I had developed the method and was progressing well but it > took me a long time and multiple tries at first. It can be done alone. > If someone is there to help they can manage the length of rail. I did > this on a hot day and I suspect thaat made the rail material much more > pliable. I am not sure that I would have been able to install the rail had it been cold. > > At the sharp corners a gap forms between the rubber rail and the boat > so I filled the space with black Boat Life sealant. > > The kit comes with plastic caps for the end. You can either put two > end caps on or use a join piece to end them together. I put a screw > through the ends of the rubber rail to make sure it did not shrink > back and then attached the link piece with a screw. The problem I ran > into, however, was that the upper pintel on the rudder would not clear > the cap. After considering various options I decided to shorten the > pintel pin, (or is that called the gudgeon?), just enough to allow the > rub rail to be cleared and then drilled a hole in the pin so that I > could secure it with a pull pin. That seemed to work fine. > > Unlike the Taco system, there is no insert that goes into the track > that will give a two-colour look - which can be attractive. > > Attached is a picture of the rail attached. Not having installed the > Tacho system I really can't say whether the Tessilmare is better or > easier to install. Certainly the rubber rail seems beefy and should > provide good protection. > > > Graham Stewart > Agile. R22, 1976 > Kingston Ontario Canada > > > > > > -------------- next part -------------- A non-text attachment was > scrubbed... > Name: Reb rail installed- Tessilmare July 2016.jpg > Type: image/jpeg > Size: 437724 bytes > Desc: not available > URL: <http://rhodes22.org/pipermail/rhodes22-list/ > attachments/20160825/1238558f/attachment.jpg> > __________________________________________________ > To subscribe/unsubscribe go to http://www.rhodes22.org/ > mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives > go to http://www.rhodes22.org/list > __________________________________________________ > __________________________________________________ To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list __________________________________________________
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 