< prior
Back to Month
Go to Thread
2018-08-19; 10:57:48 EDT
Member Since
2016-06-06
Posts: 30
It is definitely closed cell, to my knowledge all neoprene is. I looked at the different thicknesses and soft/firm and ordered two actually, a 1/4" that was more firm, and the 3/16. When I got them, decided on the 3/16, because once compressed, its basically solid rubber, and the surface of my trunk was less than perfectly smooth, so i chose it based on compress-ability. I don't believe it leaks, but its never been in the water long enough to really tell. I'd wager it does, but without having a slip to keep it in, i have no real way to know. -- CurtisSee the original archive post
On Sun, Aug 19, 2018 at 8:41 AM Graham Stewart <gstewart8 at cogeco.ca> wrote: > The neoprene that Curtis found looks great but is referred to a "sponge" > neoprene. I expect that means it is softer than the usual stuff and might > make a better seal assuming that it is closed cell. Does anyone have a more > informed opinion than mine on this difference? > > Graham > > -----Original Message----- > From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf > Of Curtis Ruck via Rhodes22-list > Sent: Saturday, August 18, 2018 7:26 PM > To: The Rhodes 22 Email List > Subject: Re: [Rhodes22-list] Rubber gasket > > I used this from Amazon: > > https://www.amazon.com/gp/product/B003HDILE4/ref=oh_aui_search_detailpage?ie=UTF8&psc=1 > on my 1979. Seems to work, but mine is only in the water ~2-3 hours a > time, and there is always water in the bilge when I start sailing (I > believe due to the cockpit drains getting clogged, and the water making up > and in the cockpit storage, which drains through to the bilge. > -- > Curtis > > > On Sat, Aug 18, 2018 at 6:40 PM Graham Stewart <gstewart8 at cogeco.ca> > wrote: > > > Just so that there is no confusion, I did make a neoprene gasket and it > is > > installed. It is 3/16 thick but has a fine ribbed pattern that I think > did > > not compress enough to make a perfect seal. It might also be too hard. > So I > > am only using the butyl to give the neoprene a smoother surface - not > > substituting the neoprene with the butyl. Nevertheless, I think I will > > replace the gasket when I can find a Canadian source. > > > > Another issue that might explain my difficulty getting a good seal is > that > > it looks to me like the flange on the cap might have been trimmed at some > > point. The lip is only about 1 1/4 inch wide and allows for only a single > > row of bolts. The base is quite a bit wider and appears to have had a > > second row of bolts at some point. It makes sense that both parts would > be > > the same width. > > > > I really don't want to take this apart again to replace the gasket and > > rebuild the cap. > > > > Graham > > > > -----Original Message----- > > From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On > Behalf > > Of Gary Novotny > > Sent: Saturday, August 18, 2018 2:40 PM > > To: The Rhodes 22 Email List > > Subject: Re: [Rhodes22-list] Rubber gasket > > > > Yep, totally agree that things bedded with urethane sealants are a bitch > > to remove. Only use this stuff as a last resort if you can’t find proper > > gasket material. Also I'd be sure the pendant and all blocks are in > > excellent condition. If not, definitely replace. The problem I see with > > Butyl for this application is that it has no adhesive properties , so > > you are counting on the cap to trunk compression to keep it sealed and > > it’s not resilient like a neoprene gasket. If the trunk is subject to > > any significant flexing at all then the compression seal could start to > > develop leaks. If I did use Butyl tape, I'd keep a close eye on it. One > > good thing is that Butyl tape would be VERY easy to replace. > > > > Gary > > > > > > On 8/18/2018 12:55 PM, Graham Stewart wrote: > > > Like Gary I used butyl extensively as a bedding material for my > hardware > > and it is a dream to use compared to other sealants. The only place below > > the waterline where I used it was the centerboard cap and only then > because > > I was getting desperate to find a solution. Gary's cautionary note is > good > > reason to keep looking for the proper neoprene - something I will do > > if/when the butyl fails or I have to remove the cap for any other reason. > > > > > > 4200 sealant is easier to remove than 5200, which is almost impossible > > without destroying the parts, but would still be extremely difficult - > > especially for such a large area. When I bought my boat a previous owner > > had used one of those high-adhesive sealants and I spent literally days > > getting the cap off using a torch to heat a large knife that I slowly > moved > > along the join. Even then I still broke the cap into two pieces and had > to > > make extensive repairs to the cap and the base. > > > > > > I don't know if there is anything like butyl that has low adhesive > > characteristics and is still rated for below the waterline use. > > > > > > For the time being the butyl is working but I will let the list know if > > it begins to fail - assuming the boat doesn't sink and take me with it. > > > > > > > > > Graham Stewart > > > Agile 1976 Rhodes 22 > > > Kingston Ontario > > > > > > > > > > > > > > > -----Original Message----- > > > From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On > > Behalf Of Gary Novotny > > > Sent: Saturday, August 18, 2018 9:38 AM > > > To: The Rhodes 22 Email List > > > Subject: Re: [Rhodes22-list] Rubber gasket > > > > > > Guys, > > > > > > I love Butyl tape, it's really great as a bedding compound. I completed > > > the first round of restoration on a boat (not my Rhodes) three months > > > ago and I used this stuff extensively for all the deck fittings and a > > > hatch. Butyl tape like all sealants needs a clean surface so use Remov > > > or DeBond first if the surface has prior sealant contamination. I can't > > > say enough good things about the ease of Butyl tape installation and > > > cleanup. All the leaking fittings are fixed now. It is too early for me > > > to report on longevity, but others have had very good results and when > > > you do need to re-bed its easy. > > > > > > I wouldn't be comfortable using this below the waterline however. If > you > > > can't get neoprene sheet, you might be better off resorting to a > > > traditional moderately adhesive sealant like 3M 4200. (Do NOT use 5200) > > > > > > Just my 2cents. > > > > > > Gary > > > > > > > > > On 8/17/2018 2:56 PM, Graham Stewart wrote: > > >> Patrick: > > >> > > >> Glad to hear that there is another Rhodie in Canada. I thought Phil > > Gautier and I were the only ones. > > >> > > >> I replaced my gasket last year but was unable to find the proper > > neoprene. I finally got some neoprene from a neighbor but it wasn't > smooth > > surfaced so it leaked no matter how many bolts I added. I finally stopped > > the leaks by using butyl tape - not an ideal solution, but it worked > well. > > Butyl is an excellent sealant but has very low adhesive qualities so it > > should be easy to remove in the future should that be necessary. The tape > > is about 3/4" wide but I only used about half of that on both sides of > the > > gasket as I didn't want to have it squeeze into the centerboard slot. I > > would not use the butyl that comes in a tube. In fact only use the butyl > if > > you can't get the proper neoprene. > > >> > > >> > > >> Graham Stewart > > >> Agile 1976 Rhodes 22 > > >> Kingston Ontario. > > >> > > >> > > >> -----Original Message----- > > >> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On > > Behalf Of Patrick Cheung > > >> Sent: Friday, August 17, 2018 2:11 PM > > >> To: The Rhodes 22 Email List > > >> Subject: Re: [Rhodes22-list] Rubber gasket > > >> > > >> Gary, > > >> > > >> I found the perfect one from Amazon but they won’t ship to Canada. > > Gonna keep looking. > > >> > > >> Thx, Patrick > > >> > > >> > > >> > > >>> On Aug 17, 2018, at 1:32 PM, Gary Novotny <gjnovotny at comcast.net> > > wrote: > > >>> > > >>> Patrick, > > >>> > > >>> When I did my centerboard trunk maintenance four years ago I used > > neoprene sheet I bought off of Amazon. It seems to have worked well. > > >>> > > >>> Gary > > >>> > > >>> Moon shadow 1978 R22 > > >>> > > >>> > > >>>> On 8/17/2018 11:50 AM, Patrick Cheung wrote: > > >>>> Dear Rhodies, > > >>>> > > >>>> It is time to repair the center board. I reached out to Stan for a > > piece of > > >>>> the rubber but he is super busy right now. > > >>>> > > >>>> I seems to recall some Rhodies may have extra rubber left over from > > their > > >>>> repair. I am hoping I can buy a stripe off you, if you are willing > to > > sell. > > >>>> > > >>>> Patrick > > >>>> Duck, '84 > > >>>> Lake Simcoe, Ontario, Canada > > >>>> __________________________________________________ > > >>>> To subscribe/unsubscribe go to > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > >>>> > > >>>> For the list Charter and help with using the mailing list and > > archives go to http://www.rhodes22.org/list > > >>>> __________________________________________________ > > >>>> > > >>> -- > > >>> Gary Novotny > > >>> 7309 S Indian River Drive > > >>> Fort Pierce Florida 34982 > > >>> 772-4660956 home > > >>> 772-9715753 cell > > >>> gjnovotny at comcast.net > > >>> > > >>> __________________________________________________ > > >>> To subscribe/unsubscribe go to > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > >>> > > >>> For the list Charter and help with using the mailing list and > archives > > go to http://www.rhodes22.org/list > > >>> __________________________________________________ > > >> __________________________________________________ > > >> To subscribe/unsubscribe go to > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > >> > > >> For the list Charter and help with using the mailing list and archives > > go to http://www.rhodes22.org/list > > >> __________________________________________________ > > >> > > >> __________________________________________________ > > >> To subscribe/unsubscribe go to > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > >> > > >> For the list Charter and help with using the mailing list and archives > > go to http://www.rhodes22.org/list > > >> __________________________________________________ > > > > -- > > Gary Novotny > > 7309 S Indian River Drive > > Fort Pierce Florida 34982 > > 772-4660956 home > > 772-9715753 cell > > gjnovotny at comcast.net > > > > __________________________________________________ > > To subscribe/unsubscribe go to > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > > For the list Charter and help with using the mailing list and archives go > > to http://www.rhodes22.org/list > > __________________________________________________ > > > > __________________________________________________ > > To subscribe/unsubscribe go to > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > > For the list Charter and help with using the mailing list and archives go > > to http://www.rhodes22.org/list > > __________________________________________________ > > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to http://www.rhodes22.org/list > __________________________________________________ > >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 