< prior
Back to Month
Go to Thread
2018-08-20; 19:58:51 EDT
Member Since
2013-07-01
Posts: 438
Yea it acts as a stop/guide for the trailing edge of the center board blade when retracted to snug up to So - ‘snugger upper’ it is. Ric Sv Dadventure Sent from my iPhoneSee the original archive post
> On Aug 20, 2018, at 6:46 PM, Graham Stewart <gstewart8 at cogeco.ca> wrote: > > Patrick > > Sounds good to me. Does anyone know what purpose the V block serves? > Graham > > -----Original Message----- > From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of Patrick Cheung > Sent: Monday, August 20, 2018 2:37 PM > To: The Rhodes 22 Email List > Subject: Re: [Rhodes22-list] Rubber gasket > > Graham, > > My boat is from 1984. I had 48 screws, I shall replace with lock nut, bolt > and washers. > > I remembered reading the archive, I am not the only one with V block, he > also had the problem with leak through the screws penetrated through the > side wall. > > This V block is approximately 6" from the Aft. The black marker line on the > flange is approx. 6" from the aft. > > My original problem is the center board unable to be lowered. After opening > the cap, I found the control line is oversized, and it is unable to pass > through 2 of the 4 blocks happily. I shall replace with 1/4" line. The rest > of the system, blocks, center board all seems to be ok. So this should be a > easy fix. Patch the 2 holes, new paint for the trunk and the board, new > neoprene. That should do it. > > patrick > > > >> On Mon, Aug 20, 2018 at 12:34 PM Graham Stewart <gstewart8 at cogeco.ca> wrote: >> >> Patrick: >> >> What year is your boat? >> >> No one else has mentioned this so I might be wrong, but I suspect that the >> V block was added by a previous owner. I don't have one in my boat. The >> only purpose I can see for it would be to stop the centerboard from being >> pushed up into the cap. On my boat, and others according to other threads, >> there a pieces of garden hose (about 6") that are placed above the pivot >> pin in the slots for the pin in the side of the housing. Should the board >> be pushed up the pieces of hose compress. I don't see the slot on your boat >> and wonder if this V block was put in the slot or perhaps the picture is >> facing towards the aft of the boat and the slots were not included. >> >> If you are repairing your rudder or centerboard you might check for voids >> - especially if there are any stress cracks or bulging in the gel coat. You >> can find the voids fairly easily by tapping on the outside with a wooden >> screwdriver handle. They can be filled fairly easily by drilling holes into >> the cavity and injecting epoxy or polyester resin. I was very surprised how >> much resin it took to fill the known cavities in both my centerboard and >> rudder. I also used three gallons of resin filling cavities in the keel but >> I had damage that may have resulted in material being lost. >> >> Your picture appears to show fewer bolt holes in the trunk than I have. >> The refit kit that Stan supplies includes 50 machine screws so I assume >> that there should ideally be holes for them all. I have 54 because I added >> a few trying to stop the leak. Since you are already doing this work, you >> might consider adding a few. >> >> The picture was also useful for me as like mine, you have a single row of >> holes so perhaps that is the design standard. If anyone has a picture of >> their housing on a more recent boat that might be very helpful. >> >> Graham >> >> -----Original Message----- >> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf >> Of Patrick Cheung >> Sent: Monday, August 20, 2018 8:49 AM >> To: Curtis Ruck; The Rhodes 22 Email List >> Subject: Re: [Rhodes22-list] Rubber gasket >> >> Graham, here’s the two pictures of the v block. Hope pictures will go >> through. >> >> I placed the order for neoprene. >> -------------- next part -------------- >> A non-text attachment was scrubbed... >> Name: image1.jpeg >> Type: image/jpeg >> Size: 77567 bytes >> Desc: not available >> URL: < >> http://rhodes22.org/pipermail/rhodes22-list/attachments/20180820/496c528a/attachment.jpeg >>> >> -------------- next part -------------- >> >> >> -------------- next part -------------- >> A non-text attachment was scrubbed... >> Name: image2.jpeg >> Type: image/jpeg >> Size: 76674 bytes >> Desc: not available >> URL: < >> http://rhodes22.org/pipermail/rhodes22-list/attachments/20180820/496c528a/attachment-0001.jpeg >>> >> -------------- next part -------------- >> >> >>> On Aug 19, 2018, at 10:57 AM, Curtis Ruck via Rhodes22-list < >> rhodes22-list at rhodes22.org> wrote: >>> >>> It is definitely closed cell, to my knowledge all neoprene is. I looked >>> at the different thicknesses and soft/firm and ordered two actually, a >> 1/4" >>> that was more firm, and the 3/16. When I got them, decided on the 3/16, >>> because once compressed, its basically solid rubber, and the surface of >> my >>> trunk was less than perfectly smooth, so i chose it based on >>> compress-ability. >>> >>> I don't believe it leaks, but its never been in the water long enough to >>> really tell. I'd wager it does, but without having a slip to keep it >> in, i >>> have no real way to know. >>> -- >>> Curtis >>> >>> >>>> On Sun, Aug 19, 2018 at 8:41 AM Graham Stewart <gstewart8 at cogeco.ca> >> wrote: >>>> >>>> The neoprene that Curtis found looks great but is referred to a "sponge" >>>> neoprene. I expect that means it is softer than the usual stuff and >> might >>>> make a better seal assuming that it is closed cell. Does anyone have a >> more >>>> informed opinion than mine on this difference? >>>> >>>> Graham >>>> >>>> -----Original Message----- >>>> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On >> Behalf >>>> Of Curtis Ruck via Rhodes22-list >>>> Sent: Saturday, August 18, 2018 7:26 PM >>>> To: The Rhodes 22 Email List >>>> Subject: Re: [Rhodes22-list] Rubber gasket >>>> >>>> I used this from Amazon: >>>> >>>> >> https://www.amazon.com/gp/product/B003HDILE4/ref=oh_aui_search_detailpage?ie=UTF8&psc=1 >>>> on my 1979. Seems to work, but mine is only in the water ~2-3 hours a >>>> time, and there is always water in the bilge when I start sailing (I >>>> believe due to the cockpit drains getting clogged, and the water making >> up >>>> and in the cockpit storage, which drains through to the bilge. >>>> -- >>>> Curtis >>>> >>>> >>>> On Sat, Aug 18, 2018 at 6:40 PM Graham Stewart <gstewart8 at cogeco.ca> >>>> wrote: >>>> >>>>> Just so that there is no confusion, I did make a neoprene gasket and it >>>> is >>>>> installed. It is 3/16 thick but has a fine ribbed pattern that I think >>>> did >>>>> not compress enough to make a perfect seal. It might also be too hard. >>>> So I >>>>> am only using the butyl to give the neoprene a smoother surface - not >>>>> substituting the neoprene with the butyl. Nevertheless, I think I will >>>>> replace the gasket when I can find a Canadian source. >>>>> >>>>> Another issue that might explain my difficulty getting a good seal is >>>> that >>>>> it looks to me like the flange on the cap might have been trimmed at >> some >>>>> point. The lip is only about 1 1/4 inch wide and allows for only a >> single >>>>> row of bolts. The base is quite a bit wider and appears to have had a >>>>> second row of bolts at some point. It makes sense that both parts would >>>> be >>>>> the same width. >>>>> >>>>> I really don't want to take this apart again to replace the gasket and >>>>> rebuild the cap. >>>>> >>>>> Graham >>>>> >>>>> -----Original Message----- >>>>> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On >>>> Behalf >>>>> Of Gary Novotny >>>>> Sent: Saturday, August 18, 2018 2:40 PM >>>>> To: The Rhodes 22 Email List >>>>> Subject: Re: [Rhodes22-list] Rubber gasket >>>>> >>>>> Yep, totally agree that things bedded with urethane sealants are a >> bitch >>>>> to remove. Only use this stuff as a last resort if you can’t find >> proper >>>>> gasket material. Also I'd be sure the pendant and all blocks are in >>>>> excellent condition. If not, definitely replace. The problem I see with >>>>> Butyl for this application is that it has no adhesive properties , so >>>>> you are counting on the cap to trunk compression to keep it sealed and >>>>> it’s not resilient like a neoprene gasket. If the trunk is subject to >>>>> any significant flexing at all then the compression seal could start to >>>>> develop leaks. If I did use Butyl tape, I'd keep a close eye on it. One >>>>> good thing is that Butyl tape would be VERY easy to replace. >>>>> >>>>> Gary >>>>> >>>>> >>>>>> On 8/18/2018 12:55 PM, Graham Stewart wrote: >>>>>> Like Gary I used butyl extensively as a bedding material for my >>>> hardware >>>>> and it is a dream to use compared to other sealants. The only place >> below >>>>> the waterline where I used it was the centerboard cap and only then >>>> because >>>>> I was getting desperate to find a solution. Gary's cautionary note is >>>> good >>>>> reason to keep looking for the proper neoprene - something I will do >>>>> if/when the butyl fails or I have to remove the cap for any other >> reason. >>>>>> >>>>>> 4200 sealant is easier to remove than 5200, which is almost impossible >>>>> without destroying the parts, but would still be extremely difficult - >>>>> especially for such a large area. When I bought my boat a previous >> owner >>>>> had used one of those high-adhesive sealants and I spent literally >> days >>>>> getting the cap off using a torch to heat a large knife that I slowly >>>> moved >>>>> along the join. Even then I still broke the cap into two pieces and had >>>> to >>>>> make extensive repairs to the cap and the base. >>>>>> >>>>>> I don't know if there is anything like butyl that has low adhesive >>>>> characteristics and is still rated for below the waterline use. >>>>>> >>>>>> For the time being the butyl is working but I will let the list know >> if >>>>> it begins to fail - assuming the boat doesn't sink and take me with it. >>>>>> >>>>>> >>>>>> Graham Stewart >>>>>> Agile 1976 Rhodes 22 >>>>>> Kingston Ontario >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> -----Original Message----- >>>>>> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On >>>>> Behalf Of Gary Novotny >>>>>> Sent: Saturday, August 18, 2018 9:38 AM >>>>>> To: The Rhodes 22 Email List >>>>>> Subject: Re: [Rhodes22-list] Rubber gasket >>>>>> >>>>>> Guys, >>>>>> >>>>>> I love Butyl tape, it's really great as a bedding compound. I >> completed >>>>>> the first round of restoration on a boat (not my Rhodes) three months >>>>>> ago and I used this stuff extensively for all the deck fittings and a >>>>>> hatch. Butyl tape like all sealants needs a clean surface so use Remov >>>>>> or DeBond first if the surface has prior sealant contamination. I >> can't >>>>>> say enough good things about the ease of Butyl tape installation and >>>>>> cleanup. All the leaking fittings are fixed now. It is too early for >> me >>>>>> to report on longevity, but others have had very good results and when >>>>>> you do need to re-bed its easy. >>>>>> >>>>>> I wouldn't be comfortable using this below the waterline however. If >>>> you >>>>>> can't get neoprene sheet, you might be better off resorting to a >>>>>> traditional moderately adhesive sealant like 3M 4200. (Do NOT use >> 5200) >>>>>> >>>>>> Just my 2cents. >>>>>> >>>>>> Gary >>>>>> >>>>>> >>>>>>> On 8/17/2018 2:56 PM, Graham Stewart wrote: >>>>>>> Patrick: >>>>>>> >>>>>>> Glad to hear that there is another Rhodie in Canada. I thought Phil >>>>> Gautier and I were the only ones. >>>>>>> >>>>>>> I replaced my gasket last year but was unable to find the proper >>>>> neoprene. I finally got some neoprene from a neighbor but it wasn't >>>> smooth >>>>> surfaced so it leaked no matter how many bolts I added. I finally >> stopped >>>>> the leaks by using butyl tape - not an ideal solution, but it worked >>>> well. >>>>> Butyl is an excellent sealant but has very low adhesive qualities so it >>>>> should be easy to remove in the future should that be necessary. The >> tape >>>>> is about 3/4" wide but I only used about half of that on both sides of >>>> the >>>>> gasket as I didn't want to have it squeeze into the centerboard slot. I >>>>> would not use the butyl that comes in a tube. In fact only use the >> butyl >>>> if >>>>> you can't get the proper neoprene. >>>>>>> >>>>>>> >>>>>>> Graham Stewart >>>>>>> Agile 1976 Rhodes 22 >>>>>>> Kingston Ontario. >>>>>>> >>>>>>> >>>>>>> -----Original Message----- >>>>>>> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On >>>>> Behalf Of Patrick Cheung >>>>>>> Sent: Friday, August 17, 2018 2:11 PM >>>>>>> To: The Rhodes 22 Email List >>>>>>> Subject: Re: [Rhodes22-list] Rubber gasket >>>>>>> >>>>>>> Gary, >>>>>>> >>>>>>> I found the perfect one from Amazon but they won’t ship to Canada. >>>>> Gonna keep looking. >>>>>>> >>>>>>> Thx, Patrick >>>>>>> >>>>>>> >>>>>>> >>>>>>>> On Aug 17, 2018, at 1:32 PM, Gary Novotny <gjnovotny at comcast.net> >>>>> wrote: >>>>>>>> >>>>>>>> Patrick, >>>>>>>> >>>>>>>> When I did my centerboard trunk maintenance four years ago I used >>>>> neoprene sheet I bought off of Amazon. It seems to have worked well. >>>>>>>> >>>>>>>> Gary >>>>>>>> >>>>>>>> Moon shadow 1978 R22 >>>>>>>> >>>>>>>> >>>>>>>>> On 8/17/2018 11:50 AM, Patrick Cheung wrote: >>>>>>>>> Dear Rhodies, >>>>>>>>> >>>>>>>>> It is time to repair the center board. I reached out to Stan for a >>>>> piece of >>>>>>>>> the rubber but he is super busy right now. >>>>>>>>> >>>>>>>>> I seems to recall some Rhodies may have extra rubber left over from >>>>> their >>>>>>>>> repair. I am hoping I can buy a stripe off you, if you are willing >>>> to >>>>> sell. >>>>>>>>> >>>>>>>>> Patrick >>>>>>>>> Duck, '84 >>>>>>>>> Lake Simcoe, Ontario, Canada >>>>>>>>> __________________________________________________ >>>>>>>>> To subscribe/unsubscribe go to >>>>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>>>>>>>> >>>>>>>>> For the list Charter and help with using the mailing list and >>>>> archives go to http://www.rhodes22.org/list >>>>>>>>> __________________________________________________ >>>>>>>>> >>>>>>>> -- >>>>>>>> Gary Novotny >>>>>>>> 7309 S Indian River Drive >>>>>>>> Fort Pierce Florida 34982 >>>>>>>> 772-4660956 home >>>>>>>> 772-9715753 cell >>>>>>>> gjnovotny at comcast.net >>>>>>>> >>>>>>>> __________________________________________________ >>>>>>>> To subscribe/unsubscribe go to >>>>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>>>>>>> >>>>>>>> For the list Charter and help with using the mailing list and >>>> archives >>>>> go to http://www.rhodes22.org/list >>>>>>>> __________________________________________________ >>>>>>> __________________________________________________ >>>>>>> To subscribe/unsubscribe go to >>>>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>>>>>> >>>>>>> For the list Charter and help with using the mailing list and >> archives >>>>> go to http://www.rhodes22.org/list >>>>>>> __________________________________________________ >>>>>>> >>>>>>> __________________________________________________ >>>>>>> To subscribe/unsubscribe go to >>>>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>>>>>> >>>>>>> For the list Charter and help with using the mailing list and >> archives >>>>> go to http://www.rhodes22.org/list >>>>>>> __________________________________________________ >>>>> >>>>> -- >>>>> Gary Novotny >>>>> 7309 S Indian River Drive >>>>> Fort Pierce Florida 34982 >>>>> 772-4660956 home >>>>> 772-9715753 cell >>>>> gjnovotny at comcast.net >>>>> >>>>> __________________________________________________ >>>>> To subscribe/unsubscribe go to >>>>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>>>> >>>>> For the list Charter and help with using the mailing list and archives >> go >>>>> to http://www.rhodes22.org/list >>>>> __________________________________________________ >>>>> >>>>> __________________________________________________ >>>>> To subscribe/unsubscribe go to >>>>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>>>> >>>>> For the list Charter and help with using the mailing list and archives >> go >>>>> to http://www.rhodes22.org/list >>>>> __________________________________________________ >>>>> >>>> __________________________________________________ >>>> To subscribe/unsubscribe go to >>>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>>> >>>> For the list Charter and help with using the mailing list and archives >> go >>>> to http://www.rhodes22.org/list >>>> __________________________________________________ >>>> >>>> >>> __________________________________________________ >>> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >>> >>> For the list Charter and help with using the mailing list and archives >> go to http://www.rhodes22.org/list >>> __________________________________________________ >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and archives go >> to http://www.rhodes22.org/list >> __________________________________________________ >> >> __________________________________________________ >> To subscribe/unsubscribe go to >> http://www.rhodes22.org/mailman/listinfo/rhodes22-list >> >> For the list Charter and help with using the mailing list and archives go >> to http://www.rhodes22.org/list >> __________________________________________________ >> > __________________________________________________ > To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list > __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list > __________________________________________________
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 