< prior
Back to Month
Go to Thread
2018-10-14; 23:17:34 EDT
Member Since
2005-04-29
Posts: 816
Thanks Chris. You are absolutely right that 90% of the work is completely hidden. GrahamSee the original archive post
-----Original Message----- From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of Chris Geankoplis Sent: Sunday, October 14, 2018 10:28 PM To: The Rhodes 22 Email List Subject: Re: [Rhodes22-list] Agile's interior Graham, What a beautiful job. So much of your work is "hidden" but it doesn't make it any less beautiful. An inspiration. Thanks On Fri, Oct 12, 2018 at 10:24 PM Graham Stewart <gstewart8 at cogeco.ca> wrote: > I thought I sent the final update on my Rhodes 22 interior rebuild last > June > but so far as I can tell I just sent it to myself. So I am sending it out > again. My apologies if this is a duplicate. > Graham > _____ > > > A long time ago I was asked to post pictures of Agile's interior when it > was > completed. Well I have finally finished the interior and can post those > pictures. > > There is nothing fancy about the interior. Certainly nothing like the > amazing carpentry of Peter Nyberg. My goal was to be efficient, cheap and > as > maintenance free as possible. There are a few bits of teak - mostly left > over from my previous install but all surfaces now are white Formica > cladding over the original or replacement plywood. Much of the trim is > aluminum and PVC. > > As I mentioned before, I shortened the galley by about 8" in order to > install a hanging locker. I use it for safety vests and rain gear but > occasionally a garment bag with good clothes when we are cruising and want > to get dressed up a bit. > > Instead of an ice box built in to the counter I use a portable cooler that > sits between the seat and the locker in front of the companion way. This > works very well for me. The cooler is quite large, portable, provides a > step > into the boat, takes up previously unused space and, as it unexpectedly > turned out, also serves to hold the companionway doors in front of the > galley storage drawers when underway. That locations turns out to be very > convenient, takes up no space and also serves to keep the galley drawers > closed when on a port heel. > > For water I found a 23L (6 gal) jerry can that just fits under the sink. I > installed a deck fill for water but have not connected it to the tank. It > is > easier for me to take the tank to the water than bring water to the tank > but > the deck fill is there when or if I or a subsequent owner needs it. On my > boat the holding tank deck outlet was within a foot of the potable water > deck fill on the starboard side deck. I was very uncomfortable with that > arrangement so when I rebuilt the deck and replaced the holding tank I > moved > the tank outlet to the other side (port) of the boat. > > The drawers are just plastic drawer units that I bought for $35. It will be > interesting to see if they last more than a few days. They come in a unit > of three drawers and that was too high to fit so I cut off the bottom > drawer > and put in a spacer that gives me a 4" space under the unit which, as it > turns out, is just the right size to store my portable three burner propane > stove. We never cook down below so using a propane stove is not a problem > and using a portable stove saves space on the galley counter. > > The floor is completely rebuilt from the hull up. The old stringers were in > bad shape and the structure under the compression post was crushed and > rotted so I had to replace everything. The new stringers are made of > pressure treated pine 5/4" deck boards that have been encapsulated in > multiple coatings of epoxy. The floor sits on the stringers and on aluminum > angle pieces running the length of the cabin at the base of the side seats > and under the galley. It is bolted down to the stringers using metal insert > nuts and to the aluminum rails using aluminum insert nuts. Previously wood > screws were used and over the years the screw holes became enlarged or > worse > and the floor boards were always loose. Hopefully this arrangement will > address that problem. > > The floor itself is 1/2" interior grade plywood that I coated in several > coats of epoxy and painted with a marine grade paint. The top is covered > with a vinyl cushion floor that is attached with contact cement. It should > be very low maintenance and nom-skid. It also brightens the interior > considerably from the dark stained wood that was there before. It has gone > through one severe winter and there are no signs that the cushion floor is > lifting - so far. There was some discussion on the list about whether 1/2" > floor boards would be adequate. I have found it to be quite adequate with > no > sense that they are soft. Maybe the 3/4" boards would be better if the > people using the boat are much heavier that Deb and I. The advantage of the > thinner boards is that they are lighter and much easier to manhandle when > they need to be removed. Also, at 6'3" I appreciate every fraction of an > inch of head space. > > I put the electrical panel on the main bulkhead. It is really unused space > and makes it very easy to service the panel from the back. I added a small > unit I got from Amazon that provides a power outlet that I use to trickle > charge the battery with a small portable solar charger. It also has two USB > charging outlets and a voltmeter. I really like being able to monitor the > battery charge so easily. Instruments and lights are the only items that > draw power and I replaced all lights with LEDs. I decided that all I really > need is a little garden tractor battery. I used big deep discharge > batteries > before but found that inevitably they were shot after a few years. I am > hoping that with the low draw and ability to monitor its state that this > inexpensive battery will suffice. We will see. > > Window frames are made of PVC trim pieces. > > In the final analysis the interior is a pretty bare bones interior but the > boat being a 1976 has always been a modest boat and does not justify going > to great expanse to refurbish. Lord knows I have already spent lots on it. > I > did splurge on new interior cushions as the old ones were utterly shot. > That > spruces things up a lot. The hull interior, where exposed, is covered with > indoor/outdoor carpeting. > > Graham Stewart > Agile. R22, 1976 > Kingston Ontario Canada > > > -------------- next part -------------- > A non-text attachment was scrubbed... > Name: Interior final June 2018 (3).jpg > Type: image/jpeg > Size: 106395 bytes > Desc: not available > URL: < > http://rhodes22.org/pipermail/rhodes22-list/attachments/20181012/6ccbf341/at tachment.jpg > > > -------------- next part -------------- > A non-text attachment was scrubbed... > Name: Interior final June 2018 (4).jpg > Type: image/jpeg > Size: 376979 bytes > Desc: not available > URL: < > http://rhodes22.org/pipermail/rhodes22-list/attachments/20181012/6ccbf341/at tachment-0001.jpg > > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to http://www.rhodes22.org/list > __________________________________________________ > __________________________________________________ To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list __________________________________________________
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 