< prior
Back to Month
Go to Thread
2019-01-08; 14:26:51 EST
Member Since
2018-11-06
Posts: 73
Thanks Graham. I will look at doing that next time I go work on the boat. AlexisSee the original archive post
On Tue, Jan 8, 2019 at 1:06 PM Graham Stewart <gstewart8 at cogeco.ca> wrote: > Alexis: > > Even in my case the repair went way overboard. The problem I faced was that > I didn't know the condition of the core until I exposed it. I could have > fixed the soft deck with epoxy injections or simply left it soft. The > problem is discerning delimitation from rot. > > Now that I see your picture the core looks pretty good to me, The only > delamination is between the core and the liner and I would not worry about > that. As long as the core is dry you should be ok. > > I see that the gel coat is cracked around some of the screw holes. I would > suggest that you open up the cracks as much as possible and fill them with > an epoxy filler. When you put the new port on chamfer the holes slightly > using a countersink bit. That will prevent cracks in the future. > > Take care, > Graham > > -----Original Message----- > From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf > Of > Alexis Seigneurin > Sent: Monday, January 7, 2019 11:24 PM > To: The Rhodes 22 Email List > Subject: Re: [Rhodes22-list] Where to find parts? > > Graham, > > It looks like you went through a very extensive restoration project. I am > seriously impressed by the amount of work you put into this. > > I don't think my boat - built in 1992- is anywhere close to that stage of > delamination. Hopefully this is just localized around the hatch... > > The picture I sent earlier can be seen here: > > http://rhodes22.org/pipermail/rhodes22-list/attachments/20190108/95e7305d/at > tachment.jpe > Alexis > > Alexis > > ________________________________ > From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> on behalf of > Graham > Stewart <gstewart8 at cogeco.ca> > Sent: Monday, January 7, 2019 10:47 PM > To: 'The Rhodes 22 Email List' > Subject: Re: [Rhodes22-list] Where to find parts? > > Alexis: > > The photos didn't come through properly. What year is your boat? Mine is an > older boat built in 1976. I know that in later years Stan substantially > improved the deck construction. > > I found that the plywood core of my boat had gradually delaminated > throughout the deck. Not only that, but the various layers of the plywood > had also delaminated and the top layer had delaminated from the deck skin > as > well. The plywood seemed to be just cheap plywood and the adhesive that > bound it all to the skins seemed to be sealant that was spread with a > calking gun very sparingly and often had not even been squeezed against the > glass. I was able to separate the liner from the plywood and remove most of > the plywood from the deck skin with my hands. What I thought might be rot, > when I found the deck had become soft, was delamination. > > I have posted photos and descriptions of what I did to repair the deck and > that should all be in the archives but if you are interested and can't find > the postings I can send it out again. In the mean time I have attached two > picture of the edge of the deck after I cut the foredeck off. You will see > the delimitation. > > If the deck isn't soft or giving you other problems I would let it pass. > The > fix, which involves injecting epoxy through the deck skin into the core is > time consuming and also requires that the deck skin be restored. That was a > huge amount of work and might well be unnecessary. > > Graham > > Graham Stewart > Agile 1976 Rhodes 22 > Kingston Ontario > > > > > > -----Original Message----- > From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf > Of > Alexis Seigneurin > Sent: Monday, January 7, 2019 9:42 PM > To: The Rhodes 22 Email List > Subject: Re: [Rhodes22-list] Where to find parts? > > It turns out I have a picture that shows the core of the deck after > removing > the hatch. I am attaching it here. > > It looks like the bottom part of the fiberglass is delaminated. Not sure > how > big of an issue this is yet... > > [Image] > > Alexis > > > ________________________________ > From: Alexis Seigneurin <alexis.seigneurin at gmail.com> > Sent: Monday, January 7, 2019 4:59 PM > To: The Rhodes 22 Email List > Subject: Re: [Rhodes22-list] Where to find parts? > > Cary: I contacted Beckson as per your suggestion for the coaming frames, > but > they don't have that :( > > Graham: that sounds good. I will inspect how much water made it into the > core. > > Thanks, > Alexis > > On Mon, Jan 7, 2019 at 3:18 PM Graham Stewart > <gstewart8 at cogeco.ca<mailto:gstewart8 at cogeco.ca>> wrote: > Alexis: > The cracks are definitely a sign that the port needs to be replaced. > > I would suggest that you try to drill into the core from inside the hole to > see how deep the water has penetrated. Hopefully not far. The holes will > also allow the core material to dry out faster and allow for the epoxy to > penetrate further if you use a syringe. If the damp wood does not go too > far, I would use something like a dremmel tool to remove it and then seal > with epoxy and fill with thickened epoxy. > > If the wood is wet further in than what you can remove you might have a > more > involved repair on your hands. In that case I would drill up through the > liner in a pattern of holes that fan out from the hole until you hit dry > wood. Drill lots of holes where the wood is wet. You now need to let it dry > out. Test for dryness with new holes. It might take a long time unless you > can figure out a way to push warm air into the core. I used a shop vac for > this purpose. You would then need to figure out a way to inject epoxy into > the core without it all running back out -perhaps with tape. When I did > mine > I drilled the holes from above because I knew I was going to glass and > paint > the whole deck anyway. That meant that the epoxy didn't drip through. It > might still be easier even if you have to patch a section of the deck. > > I had a leak around a holding tank vent in my dick. I actually removed the > deck and separated the liner and removed the core plywood - something that > turned out to be unnecessary. My point in telling you this is that when I > got to examine the plywood I found that while the hole for the vent was > only > about 1/2" in diameter, the wet plywood extended out about a foot. If I had > sealed the edge of the plywood at the hole when it was dry I would have > sealed in all the water-infused plywood that was further in. > > Hopefully you caught the leak early on and none of this is necessary. > > > Graham Stewart > Agile 1976 Rhodes 22 > Kingston Ontario > > > > > -----Original Message----- > From: Rhodes22-list > [mailto:rhodes22-list-bounces at rhodes22.org<mailto: > rhodes22-list-bounces at rhod > es22.org>] On Behalf Of > Alexis Seigneurin > Sent: Monday, January 7, 2019 2:32 PM > To: The Rhodes 22 Email List > Subject: Re: [Rhodes22-list] Where to find parts? > > Thanks all for your replies and suggestions. > > Just to confirm, the water on the ceiling of the v-berth *is* condensation: > water leaks into the triangular tray/bucket, accumulates there, then > temperature changes make the water condensate on the ceiling (boat is in > Deltaville, and Sunday was a warm day, but night was cold). Water is > localized in the v-berth, thus eliminating the bilge as a source of water, > and doesn't condensate on areas where the deck is thicker (see the picture > I had attached in my first email). > > The reason why I am looking at replacing the hatch rather than just > re-sealing it is because the plastic is brittle and is cracked around 2 of > the screws. > > The sealant that was used is silicone. Not very durable, so I'm not > surprised it has to be re-sealed. The plywood core had not been protected > when installing this hatch, though, so it is wet. It if not soft, though, > so my hope is I can get it to dry before sealing it with epoxy and > installing a new hatch. > > I like the idea of the Nicro vent as I am thinking of keeping the anchor in > the lazarette. Thanks Mary Lou for the suggestion. > > Alexis > > On Mon, Jan 7, 2019 at 11:52 AM Cary Tolbert > <retiredtoby at gmail.com<mailto:retiredtoby at gmail.com>> wrote: > > > Alexis, for parts to the existing ports on a Rhodes 22 please try Beckson > > Marine. This is the OME parts place. > > You can even print their installation instructions. They will sell direct > > to individuals and are located in Bridgeport, CT. > > > > > > > > Cary Tolbert > > S/V Whisper '86 > > > > > > On Mon, Jan 7, 2019 at 11:30 AM Graham Stewart > <gstewart8 at cogeco.ca<mailto:gstewart8 at cogeco.ca>> > > wrote: > > > > > Alexis: > > > > > > All the responses before mine are completely sensible. I also wonder > > > whether > > > the source is really the deck hatch or condensation. Pouring water on > the > > > hatch would tell you if it is leaking. Further, you would want to know > if > > > the leak is between the outside of the port and the deck hole or the > > inside > > > where it is threaded. If it leaks around the outside then, as others > > > suggest, rebedding is what is sufficient - provided, of course that you > > can > > > get it out of the deck hole without destroying it. If silicone was used > > it > > > should not be difficult to remove and also would likely explain why it > is > > > leaking. If something like 5200 was used, you might need dynamite to > get > > it > > > out. > > > > > > If the port is leaking internally, replacement is probably the best > > choice. > > > If the leak is around the outside seal be sure to check your core > > material > > > incase water has been entering the core and doing its nasty work. In > any > > > event I would strongly recommend that you seal the core edge very well > > with > > > epoxy and not rely solely on sealant. By the way, I like to use butyl > > tape > > > rather than sealant in such places if there is any possibility that you > > > might need to remove the hatch again in the future. > > > > > > As for the coaming frame, if you can't get one from Stan or anyone else > > you > > > might do what I did and install edge trim such as this: > > > > > > > > > > https://www.amazon.ca/gp/product/B00KGAKG2G/ref=oh_aui_detailpage_o06_s00?ie > > > =UTF8&psc=1 > > > < > > > > https://www.amazon.ca/gp/product/B00KGAKG2G/ref=oh_aui_detailpage_o06_s00?ie > =UTF8&psc=1 > <https://www.amazon.ca/gp/product/B00KGAKG2G/ref=oh_aui_detailpage_o06_s00?ie=UTF8&psc=1> > <https://www.amazon.ca/gp/product/B00KGAKG2G/ref=oh_aui_detailpag > e_o06_s00?ie=UTF8&psc=1 > <https://www.amazon.ca/gp/product/B00KGAKG2G/ref=oh_aui_detailpage_o06_s00?ie=UTF8&psc=1> > > > > > > > > . Note that is the Canadian Amazon site and you would want to > > > look it up on the US site. The frame would certainly look much better > if > > > you > > > can find it. > > > > > > > > > Graham Stewart > > > Agile 1976 Rhodes 22 > > > Kingston Ontario > > > > > > > > > > > > -----Original Message----- > > > From: Rhodes22-list > [mailto:rhodes22-list-bounces at rhodes22.org<mailto: > rhodes22-list-bounces at rhod > es22.org>] On > > Behalf > > > Of > > > Alexis Seigneurin > > > Sent: Sunday, January 6, 2019 10:54 PM > > > To: The Rhodes 22 Email List > > > Subject: [Rhodes22-list] Where to find parts? > > > > > > Hi there, > > > > > > I found today that there was quite a lot of water on the ceiling of the > > > V-berth of my boat (see attached picture). Fortunately, there's some > kind > > > of triangular bucket that collects this water, so nothing got damaged > in > > > the V-berth. > > > > > > I found that the inspection hatch that is at the bow of the boat was > the > > > culprit for this leak. I went to West Marine but couldn't find a > > > replacement. The inside diameter is 3-1/2", but the smallest that was > > > available in store was 4". > > > > > > My questions are: > > > - What is this hatch used for? > > > - Should I replace this hatch with an identical one, or should I open a > > > larger hole to fit a 4" hatch? > > > - If I should get an identical hatch, any idea where I can find one? > > > > > > I would also like to replace the plastic frame of the cockpit shelves. > > One > > > of them is broken, but again, West Marine doesn't seem to have that in > > > store. Do you happen to know where I can find replacement parts? > > > > > > Pictures attached so that you can see what I mean. > > > > > > Thanks! > > > Alexis > > > -------------- next part -------------- > > > A non-text attachment was scrubbed... > > > Name: IMG_7020.jpg > > > Type: image/jpeg > > > Size: 261546 bytes > > > Desc: not available > > > URL: > > > < > > > > > > http://rhodes22.org/pipermail/rhodes22-list/attachments/20190106/58539771/a > > > ttachment.jpg > > > < > > > > http://rhodes22.org/pipermail/rhodes22-list/attachments/20190106/58539771/at > tachment.jpg > <http://rhodes22.org/pipermail/rhodes22-list/attachments/20190106/58539771/attachment.jpg> > <http://rhodes22.org/pipermail/rhodes22-list/attachments/2019010 > 6/58539771/attachment.jpg > <http://rhodes22.org/pipermail/rhodes22-list/attachments/20190106/58539771/attachment.jpg> > > > > > > > > > > > > -------------- next part -------------- > > > A non-text attachment was scrubbed... > > > Name: IMG_7055.jpg > > > Type: image/jpeg > > > Size: 292523 bytes > > > Desc: not available > > > URL: > > > < > > > > > > http://rhodes22.org/pipermail/rhodes22-list/attachments/20190106/58539771/a > > > ttachment-0001.jpg > > > < > > > > http://rhodes22.org/pipermail/rhodes22-list/attachments/20190106/58539771/at > tachment-0001.jpg > <http://rhodes22.org/pipermail/rhodes22-list/attachments/20190106/58539771/attachment-0001.jpg> > <http://rhodes22.org/pipermail/rhodes22-list/attachments/20 > 190106/58539771/attachment-0001.jpg > <http://rhodes22.org/pipermail/rhodes22-list/attachments/20190106/58539771/attachment-0001.jpg> > > > > > > > > > > > > -------------- next part -------------- > > > A non-text attachment was scrubbed... > > > Name: IMG_7050.jpg > > > Type: image/jpeg > > > Size: 119643 bytes > > > Desc: not available > > > URL: > > > < > > > > > > http://rhodes22.org/pipermail/rhodes22-list/attachments/20190106/58539771/a > > > ttachment-0002.jpg > > > < > > > > http://rhodes22.org/pipermail/rhodes22-list/attachments/20190106/58539771/at > tachment-0002.jpg > <http://rhodes22.org/pipermail/rhodes22-list/attachments/20190106/58539771/attachment-0002.jpg> > <http://rhodes22.org/pipermail/rhodes22-list/attachments/20 > 190106/58539771/attachment-0002.jpg > <http://rhodes22.org/pipermail/rhodes22-list/attachments/20190106/58539771/attachment-0002.jpg> > > > > > > > > > > > > -------------- next part -------------- > > > A non-text attachment was scrubbed... > > > Name: IMG_7035.jpg > > > Type: image/jpeg > > > Size: 132791 bytes > > > Desc: not available > > > URL: > > > < > > > > > > http://rhodes22.org/pipermail/rhodes22-list/attachments/20190106/58539771/a > > > ttachment-0003.jpg > > > < > > > > http://rhodes22.org/pipermail/rhodes22-list/attachments/20190106/58539771/at > tachment-0003.jpg > <http://rhodes22.org/pipermail/rhodes22-list/attachments/20190106/58539771/attachment-0003.jpg> > <http://rhodes22.org/pipermail/rhodes22-list/attachments/20 > 190106/58539771/attachment-0003.jpg > <http://rhodes22.org/pipermail/rhodes22-list/attachments/20190106/58539771/attachment-0003.jpg> > > > > > > > > > > > > __________________________________________________ > > > To subscribe/unsubscribe go to > > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > > > > For the list Charter and help with using the mailing list and archives > go > > > to > > > http://www.rhodes22.org/list > > > __________________________________________________ > > > > > > __________________________________________________ > > > To subscribe/unsubscribe go to > > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > > > > For the list Charter and help with using the mailing list and archives > go > > > to http://www.rhodes22.org/list > > > __________________________________________________ > > > > > __________________________________________________ > > To subscribe/unsubscribe go to > > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > > > For the list Charter and help with using the mailing list and archives go > > to http://www.rhodes22.org/list > > __________________________________________________ > > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to > http://www.rhodes22.org/list > __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to > http://www.rhodes22.org/list > __________________________________________________ > -------------- next part -------------- > A non-text attachment was scrubbed... > Name: Image-2.png > Type: image/jpeg > Size: 996181 bytes > Desc: Image-2.png > URL: > < > http://rhodes22.org/pipermail/rhodes22-list/attachments/20190108/95e7305d/a > ttachment.jpe> > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to > http://www.rhodes22.org/list > __________________________________________________ > -------------- next part -------------- > A non-text attachment was scrubbed... > Name: Rhodes foredeck removed July 2009 a.jpg > Type: image/jpeg > Size: 39426 bytes > Desc: not available > URL: > < > http://rhodes22.org/pipermail/rhodes22-list/attachments/20190107/f0403af5/a > ttachment.jpg > <http://rhodes22.org/pipermail/rhodes22-list/attachments/20190107/f0403af5/attachment.jpg> > > > -------------- next part -------------- > A non-text attachment was scrubbed... > Name: Rhodes deck delamination July 2009 a.jpg > Type: image/jpeg > Size: 47049 bytes > Desc: not available > URL: > < > http://rhodes22.org/pipermail/rhodes22-list/attachments/20190107/f0403af5/a > ttachment-0001.jpg > <http://rhodes22.org/pipermail/rhodes22-list/attachments/20190107/f0403af5/attachment-0001.jpg> > > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to > http://www.rhodes22.org/list > __________________________________________________ > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to > http://www.rhodes22.org/list > __________________________________________________ > > __________________________________________________ > To subscribe/unsubscribe go to > http://www.rhodes22.org/mailman/listinfo/rhodes22-list > > For the list Charter and help with using the mailing list and archives go > to http://www.rhodes22.org/list > __________________________________________________ >
To use your email application to send a messsage to the webmaster rather than this form, .
Your post is being sent... 