show less <<<
On Tue, Jun 18, 2019 at 8:47 PM Mike Riter <mike at traildesign.com > wrote:
> Ha! Yup. I'll correct the drawing. Thanks for catching that Hank.
>
> Michael Riter
> President, Trail Design Specialists, Inc.
> Lead Instructor, Trail Master and mechanized training
> mike at traildesign.com
> 678-410-8021
>
>
>
> On Tue, Jun 18, 2019 at 5:07 PM Hank <hnw555 at gmail.com > wrote:
>
> > Hey Mike,
> >
> > Hopefully not a dumb question, but it looks like you have the relay coils
> > both going to the same contact on the motor. Wouldn't they need to go to
> > opposite contacts to reverse the direction of the motor?
> >
> > Hank
> >
> > On Tue, Jun 18, 2019 at 6:04 PM Mike Riter <mike at traildesign.com > wrote:
> >
> > > No worries Bob.
> > > I was just looking at my drawing and realized you don’t need a 30 amp
> > rated
> > > switch since the switch is only powering the relay coils. I would
> > recommend
> > > the best water tight, marine grade switch you can get that’s rated for
> a
> > > few amps higher than either of the relays.
> > >
> > > On Tue, Jun 18, 2019 at 4:07 PM Bob Garrant <bgarrant at gmail.com >
> wrote:
> > >
> > > > Mike,
> > > > The attachment came through. Very helpful. And just in time because
> the
> > > > remote seems like it’s about to ‘expire’.
> > > > Thanks very much,
> > > > Bob
> > > >
> > > >
> > > > On Tue, Jun 18, 2019 at 4:13 PM Mike Riter <mike at traildesign.com >
> > wrote:
> > > >
> > > > > The switch needs to go through isolation relays to prevent back
> > feeding
> > > > the
> > > > > system. The relays should already be there. You'll need to remove
> the
> > > > > wireless control and wire a SPDT switch rated for at least 30 amps
> in
> > > its
> > > > > place. I put together a drawing showing how it should be wired.
> > > > >
> > > > > Michael Riter
> > > > > President, Trail Design Specialists, Inc.
> > > > > Lead Instructor, Trail Master and mechanized training
> > > > > mike at traildesign.com
> > > > > 678-410-8021
> > > > >
> > > > >
> > > > >
> > > > > On Tue, Jun 18, 2019 at 2:10 PM Peter Nyberg <
> peter at sunnybeeches.com
> > >
> > > > > wrote:
> > > > >
> > > > > > The attachment came through for me. The link is at the very
> bottom
> > > of
> > > > > the
> > > > > > message.
> > > > > >
> > > > > > Peter Nyberg
> > > > > > Coventry, CT
> > > > > > s/v Silverheels (1988/2016)
> > > > > >
> > > > > >
> > > > > >
> > > > > > > On Jun 18, 2019, at 2:47 PM, Mark West via Rhodes22-list <
> > > > > > rhodes22-list at rhodes22.org > wrote:
> > > > > > >
> > > > > > > sorry the attachment did not go?
> > > > > > >
> > > > > > >
> > > > > > > -----Original Message-----
> > > > > > > From: Mark West via Rhodes22-list <rhodes22-list at rhodes22.org >
> > > > > > > To: rhodes22-list <rhodes22-list at rhodes22.org >
> > > > > > > Sent: Tue, Jun 18, 2019 2:34 pm
> > > > > > > Subject: Re: [Rhodes22-list] Covert Badlands 2500 Winch from
> > remote
> > > > to
> > > > > > rocker switch?
> > > > > > >
> > > > > > > I would remove the remote system, then rewire manual switch 1
> > > system
> > > > > > could back feed other and let the magic blue smoke out. mine
> needed
> > > 30
> > > > > amp
> > > > > > fuse I think this attachment is how I wire it Mark s/v Fairwind
> 2
> > > > > > > -----Original Message-----
> > > > > > > From: Bgarrant <Bgarrant at gmail.com >
> > > > > > > To: rhodes22-list <rhodes22-list at rhodes22.org >
> > > > > > > Sent: Tue, Jun 18, 2019 10:20 am
> > > > > > > Subject: [Rhodes22-list] Covert Badlands 2500 Winch from remote
> > to
> > > > > > rocker switch?
> > > > > > >
> > > > > > > I want to convert the Badlands 2500 Winch Motor for my motor
> lift
> > > > from
> > > > > a
> > > > > > > wireless remote to a rocker switch. I would appreciate guidance
> > for
> > > > > doing
> > > > > > > this. It seems pretty straightforward but maybe I’m overlooking
> > > > > > something.
> > > > > > > Thanks,
> > > > > > > Bob Garrant
> > > > > > > s/v Sail la Vie 2000
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > > --
> > > > > > > Sent from: http://rhodes-22.1065344.n5.nabble.com/
> > > > > > > -------------- next part --------------
> > > > > > > A non-text attachment was scrubbed...
> > > > > > > Name: Untitled.png
> > > > > > > Type: image/png
> > > > > > > Size: 26970 bytes
> > > > > > > Desc: not available
> > > > > > > URL: <
> > > > > >
> > > > >
> > > >
> > >
> >
> http://rhodes22.org/pipermail/rhodes22-list/attachments/20190618/b39bb15c/attachment.png
> > > > > > >
> > > > > > > -------------- next part --------------
> > > > > > > A non-text attachment was scrubbed...
> > > > > > > Name: switch.png
> > > > > > > Type: image/png
> > > > > > > Size: 26970 bytes
> > > > > > > Desc: not available
> > > > > > > URL: <
> > > > > >
> > > > >
> > > >
> > >
> >
> http://rhodes22.org/pipermail/rhodes22-list/attachments/20190618/984ca6e7/attachment.png
> > > > > > >
> > > > > >
> > > > > >
> > > > > -------------- next part --------------
> > > > > A non-text attachment was scrubbed...
> > > > > Name: SPDT reversible switch.jpg
> > > > > Type: image/jpeg
> > > > > Size: 599311 bytes
> > > > > Desc: not available
> > > > > URL: <
> > > > >
> > > >
> > >
> >
> http://rhodes22.org/pipermail/rhodes22-list/attachments/20190618/f5cc30a3/attachment.jpg
> > > > > >
> > > > >
> > > >
> > > --
> > > Michael Riter
> > > President, Trail Design Specialists, Inc.
> > > Lead Instructor, Trail Master and mechanized training
> > > mike at traildesign.com
> > > 678-410-8021
> > >
> >
>
show less <<<